Jr Instructor (Mechanic Consumer Electronic Appliances)-Industrial Training Dept-(CAT NO 595/2017)

FINAL ANSWER KEY
Question Paper Code: 62/2019/OL
Category Code: 595/2017
Exam: Jr Instructor (Mechanic Consumer Electronic Appliances)
Date of Test 11-12-2019
Department Industrial Training
Alphacode A
Question1:-The capacity of a battery is expressed in
A:-Amperes
B:-Ampere-hour
C:-Watts
D:-Watt-hour
Correct Answer:- Option-B
Question2:-Speed of a universal motor is
A:-Dependent on frequency of supply
B:-Proportional to frequency of supply
C:-Independent of frequency of supply
D:-None of these
Correct Answer:- Option-C
Question3:-A cylindrical wire one meter in length has a resistance of 100Ω. What would be the resistance of wire made from the same material if both the length and cross-sectional
area are doubled?
A:-200 ohm
B:-400 ohm
C:-100 ohm
D:-50 ohm
Correct Answer:- Option-C
Question4:-Semi conductor have _____ temperature Co-efficient
A:-Zero
B:-Positive
C:-Negative
D:-None of these
Correct Answer:- Option-C
Question5:-Power factor of a R-L-C parallel circuit is
A:-zero
B:-0.8 lagging
C:-0.8 leading
D:-Unity
Correct Answer:- Option-D
Question6:-_____ damping method is common in moving coil instrument
A:-Eddy current
B:-Fluid
C:-Air
D:-Spring
Correct Answer:- Option-A
Question7:-An auto-transformer consists of 200 turns. Winding is connected to 200V AC supply main for getting 24V output. The winding should be tapped at _____ turns number
A:-12
B:-24
C:-100
D:-72
Correct Answer:- Option-B
1 of 13
Question8:-a six pole induction motor is connected to 50 c/s supply. It is running at 970 rpm. Find the percentage of slip
A:-30%
B:-0.3%
C:-0.03%
D:-3%
Correct Answer:- Option-D
Question9:-The material used for fuse must have
A:-Low melting point and high specific resistance
B:-Low melting point and any specific resistance
C:-Low melting point and low specific resistance
D:-High melting point and low specific resistance
Correct Answer:- Option-A
Question10:-In an inductive circuit, the inductance of 0.02 Henry is connected to 200 V, 50 c/s supply. Inductive reactance is
A:-628Ω
B:-62.8 Ω
C:-6.28 Ω
D:-6280 Ω
Correct Answer:- Option-C
Question11:-Processing of data in computers is done under the control of sets of instructions, is termed as _____
A:-Data instruction
B:-Information
C:-Programs
D:-None of these
Correct Answer:- Option-C
Question12:-In Windows, Resetting of system date and time can be done using
A:-Control Panel
B:-Calendar
C:-Devices & Printers
D:-Accessories
Correct Answer:- Option-A
Question13:-To install new font the sequence of command is
A:-Start -> setting -> control panel -> font
B:-Start -> setting -> control panel -> font -> install new font
C:-Start -> control panel -> font -> install new font
D:-Start -> setting -> font
Correct Answer:-Question Cancelled
Question14:-_____ is a secondary Storage Device
A:-DVD
B:-CDR&W
C:-Memory Cards
D:-All these
Correct Answer:- Option-D
Question15:-Which printer cable use male DB-25 connecter to connect with a computer
A:-Serial
B:-USB
C:-Parallel
D:-None of these
Correct Answer:- Option-C
Question16:-Which device use friction feed mechanism to load paper into the print assembly?
A:-Laser Printer
2 of 13
B:-Dot Matrix printer
C:-Line Printer
D:-None of these
Correct Answer:- Option-A
Question17:-Which of the following command is used in Ms Word to open “find and replace” dialogue box with activating “go to tab” is
A:-Ctrl + O
B:-Ctrl + F
C:-Ctrl + G
D:-Ctrl + H
Correct Answer:- Option-C
Question18:-In Ms Word pressing F8 three times selects _____
A:-Paragraph
B:-Word
C:-Page
D:-Sentence
Correct Answer:- Option-D
Question19:-In excel, a function inside another function is called _____
A:-Roundoff
B:-Nested
C:-Mode
D:-Conditional
Correct Answer:- Option-B
Question20:-_____ function is used in Excel to find the largest number in a series of numbers
A:-Maximum
B:-High
C:-Highest
D:-Max
Correct Answer:- Option-D
Question21:-In a conductor the resistance changes with _____
A:-Voltage
B:-Temperature
C:-Current
D:-Humidity
Correct Answer:- Option-B
Question22:-The letter C is the symbol for _____
A:-Impedance
B:-Capacitance
C:-Current
D:-Charge
Correct Answer:- Option-B
Question23:-An ideal volt meter is connecting to a 200 V supply having internal resistance of 10 ohms. What will be the reading of the volt meter
A:-Exact 20 Volt
B:-Just below 20 Volt
C:-Exact 200 Volt
D:-Just below 200 Volt
Correct Answer:- Option-C
Question24:-Which of the following diode is used in detector stage of an AM receiver
A:-OA 79
B:-BY 127
C:-IN4001
3 of 13
D:-All of the above
Correct Answer:- Option-A
Question25:-In low frequency transformers the core materials are generally soft silicon steel because
A:-They are having large hysteresis loop area
B:-They are having least coercivity
C:-They are having high coercivity
D:-High retentivity
Correct Answer:- Option-B
Question26:-the expected energy of electrons at absolute zero is known as
A:-Workfunction
B:-Fermi level energy
C:-Emission energy
D:-Forbidden energy
Correct Answer:- Option-B
Question27:-The first storage location of stack operation in 8051 microcontroller is
A:-00H
B:-01H
C:-07H
D:-08H
Correct Answer:- Option-D
Question28:-After the execution of the instruction “move A, 20H”
A:-Accumulator content is the content of the memory location 20H
B:-Accumulator content is 20H
C:-The content of accumulator moves to the memory location 20 H
D:-The stack pointer points to the memory location 20H
Correct Answer:- Option-A
Question29:-MOV A, @R0 is
A:-Register addressing
B:-Indexed addressing
C:-Register indirect addressing
D:-Immediate addressing
Correct Answer:- Option-C
Question30:-The one and only register inside the CPU holds 16 bit address of the instructions is
A:-DPTR
B:-Program counter
C:-Stack pointer
D:-Instruction decoder
Correct Answer:- Option-B
Question31:-After the execution of the following instructions,
mov SP, #08H
MOV R1, #12H
MOV R4, #0F3H
Push 1
Push 4
The stack pointer points to which location?
A:-08H
B:-09H
C:-10H
D:-0AH
Correct Answer:- Option-D
Question32:-The unit of modulation index is
A:-Unitless
4 of 13
B:-Hertz
C:-Volt
D:-Volt/microsecond
Correct Answer:- Option-A
Question33:-Whenever there is a temperature gradient in a conductive material, an e.m.f will induce and the gradient of voltage is proportional to the gradient in temperature. This is
known as
A:-Stroboscopic effect
B:-Seebeck effect
C:-Hall effect
D:-Esaki effect
Correct Answer:- Option-B
Question34:-The working of OFC is based on the principle
A:-Total internal reflection
B:-Total internal defraction
C:-Total internal refraction
D:-Total radiation
Correct Answer:- Option-A
Question35:-Which value of BCD input activates all segments of the seven segment decoder IC 7447
A:-1001
B:-1111
C:-1000
D:-0000
Correct Answer:- Option-C
Question36:-The wavelength of 2-GHz wave is:
A:-15 cm
B:-15 mm
C:-1.5 cm
D:-1.5 mm
Correct Answer:- Option-A
Question37:-The cross talk due to the electromagnetic interferance can be eliminated by
A:-Placing a high value inductor in series with the transmission line
B:-Using capacitance network in parallel with the transmission line
C:-Twisting the copper wires
D:-A stub of appropriate length is placed at some distance from the load
Correct Answer:- Option-C
Question38:-The insulation thickness in conductor of a cable depend on
A:-power handling ability of cable
B:-Applied voltage
C:-Current carrying capability of cable
D:-The length of the cable
Correct Answer:- Option-B
Question39:-In multi digit seven segment displays, the Ripple Blank Input and Ripple Blank Outputs are used for
A:-Dynamic display in order to save power and to increase the life of the display
B:-Blank out the all the zeros and make it look more intelligent
C:-Cascading the display otherwise displays not works synchronously
D:-Blank out the leading zeros and make it look more intelligent
Correct Answer:- Option-D
Question40:-A 1KVA, 12V online ups connected to a load of 500 Watts, the battery used is 100Ah, then what will be the back up time if the losses are negligible
A:-120 minutes
B:-2 hour and 40 minutes
5 of 13
C:-144 minutes
D:-2.6 hours
Correct Answer:- Option-C
Question41:-Candela is the unit for
A:-Light flux
B:-Luminous intensity
C:-Wavelength
D:-Luminous efficiency
Correct Answer:- Option-B
Question42:-Which of the following is not true in case of a DSO.
A:-The waveforms are stored in memory to enable them to be processed as needed.
B:-The accuracy of DSO is higher than that of analogue scopes
C:-It is possible to programme the DSO to high level of functionality
D:-It has low input impedance which enables the conversion of ADC faster
Correct Answer:- Option-D
Question43:-Manganin is the alloy of
A:-Copper, Manganese and Nickel
B:-Copper, Magnesium and Nickel
C:-Manganese, Gallium, Nickel and Iron
D:-Manganese, Copper,Gallium, Nickel
Correct Answer:- Option-A
Question44:-Which type of transducer is generally used in electronic weighing machines
A:-Inductive
B:-Capacitive
C:-Resistive
D:-All of the above
Correct Answer:- Option-C
Question45:-What will be the output when one of the Zener diode short in the zener diode peak clipper
A:-Only one half cycle in the output which resembles halfwave rectifier output
B:-No output due to the short circuited zener diode
C:-The output is only the peak portion of one half cycle
D:-The output is the peak clipped halfwave output
Correct Answer:- Option-D
Question46:-At room temperature, a silicon crystal act like
A:-Conductor
B:-Insulator
C:-Semiconductor
D:-Super conductor
Correct Answer:- Option-B
Question47:-Which of the following solid state device is fastest
A:-BJT
B:-IGBT
C:-MOSFET
D:-SCR
Correct Answer:- Option-C
Question48:-Which of the following is not true in companding
A:-Compressing the signal before input to an Analog to digital converter
B:-Which expanding the signal after a Digital to analog converter
C:-It increases the signal to noise ratio (SNR) at rreduced bit rates
D:-Higher SnR can be achieved by uniform quantization rather than non uniform
6 of 13
Correct Answer:- Option-D
Question49:-What is the effective band width of a two stage cascaded amplifier each having a band width of one mega hertz(1MHz)
A:-640KHz
B:-1640KHz
C:-885KHz
D:-500KHz
Correct Answer:- Option-A
Question50:-What is the maximum allowable tracking error frequency in amplitude modulation
A:-+/- 1KHz
B:-+/- 2KHz
C:-+/- 3 KHz
D:-+/- 5KHz
Correct Answer:- Option-C
Question51:-The 78XX series regulator Ics are commonly found in the through hole package of
A:-T0 92
B:-T0 220
C:-T0 18
D:-T0 206A
Correct Answer:- Option-B
Question52:-The decimal number 16 is equivalent to the hexadecimal
A:-11H
B:-10H
C:-A0 H
D:-01H
Correct Answer:- Option-B
Question53:-PWM can be generated by
A:-Astable multivibrator
B:-Bistable multivibrator
C:-Monostable multivibrator
D:-Schmitt trigger
Correct Answer:- Option-C
Question54:-During the counting because of noise spikes, the counter may goes to some unused state and the subsequent clock pulses may causes the counter to move from one
unused state to another unused state is known as
A:-Lockout
B:-Fly Wheel
C:-Corona
D:-Moore
Correct Answer:- Option-A
Question55:-Which colour LEDs has the highest forward voltage drop generally
A:-Red
B:-Blue
C:-Green
D:-White
Correct Answer:- Option-D
Question56:-A half wave dipole at a frequency of 200 MHz has a length of
A:-200 metre
B:-1.5 metre
C:-3 metre
D:-6 m
Correct Answer:- Option-B
7 of 13
Question57:-The thickness of PCB used for surface mount devices is
A:-0.8 mm to 1 mm
B:-1.5 mm to 2 mm
C:-0.2 mm to 2 mm
D:-above 2 mm
Correct Answer:- Option-A
Question58:-Which of the following is not a feature or advantage of FPGS over micro controller
A:-FPGA doesn’t have a fixed hardware structure
B:-Ability of parallel processing
C:-Process larger data with few clock cycle
D:-Low cost
Correct Answer:- Option-D
Question59:-The LEDs operate in visible range, only when the semiconductor should have the band gap energy
A:-Above 3.2eV
B:-Between 1.4 to 3.0eV
C:-Less than 1eV
D:-Between 1eV to 1.32eV
Correct Answer:- Option-B
Question60:-Which of the following is a photo emissive material
A:-Selenium
B:-Telurium
C:-Polonium
D:-Cesium silver
Correct Answer:- Option-D
Question61:-Which of the following is a non-renewable source of energy
A:-Tidal power
B:-Geothermal energy
C:-Nuclear energy
D:-Wind power
Correct Answer:- Option-C
Question62:-The electrical apparatus that provides power to load when mains power fails is known as
A:-USB
B:-UPS
C:-UCP
D:-UPC
Correct Answer:- Option-B
Question63:-Which one of the following is an impact printer
A:-Dot matrix
B:-Inkjet
C:-Laser
D:-None of these
Correct Answer:- Option-A
Question64:-The maximum operating voltage of LCD panel may be
A:-100v
B:-10v
C:-1v
D:-0.1v
Correct Answer:- Option-C
Question65:-The maximum usual idagonal six of the LCD panel is
A:-160cm
8 of 13
B:-260cm
C:-360cm
D:-460cm
Correct Answer:- Option-A
Question66:-The principle of LCD display is
A:-Twisted pneumatic
B:-Pneumatics
C:-Thermocouple
D:-Vaccum display
Correct Answer:- Option-A
Question67:-In a 7 segment display system the decimal point is displayed by
A:-any one of the 7 bit
B:-f bit
C:-a separate 8th bit
D:-g bit
Correct Answer:- Option-C
Question68:-An UPS which does not require inverter is _____
A:-Online UPS
B:-Offline UPS
C:-DC power UPS
D:-Line interactive UPS
Correct Answer:- Option-C
Question69:-In a UPS the failure of AC input supply is indicated by
A:-Red lightnonly
B:-A buzzer only
C:-Both red light and buzzer
D:-None of these
Correct Answer:- Option-C
Question70:-The desirable changeover period for a UPS is _____
A:-2 ms
B:-5 ms
C:-10 ms
D:-1 ms
Correct Answer:- Option-D
Question71:-Solar energy is _____ resource of energy
A:-Consumable
B:-Renewable
C:-Dangerous
D:-Negligible
Correct Answer:- Option-B
Question72:-A solar panel is usually designed to generate _____ volts DC
A:-1-2 V
B:-3-5 V
C:-6-7 V
D:-12-20 V
Correct Answer:- Option-D
Question73:-Which device is used in remote control operated electronic equipment to work as an acceptor for the remote signal
A:-Zener diode
B:-Photo diode
C:-IR LED
9 of 13
D:-Photo voltaic cell
Correct Answer:- Option-B
Question74:-The overall thickness of a LED is abaout
A:-1.5 cm
B:-2.5 cm
C:-3.5 cm
D:-4.5 cm
Correct Answer:- Option-B
Question75:-A LCD panel is not a self illuminated panel. For illuminating this panel _____ are used as backlight devices
A:-100 w lamp
B:-20 w fluorescent tube
C:-CCFL
D:-Electric arc lamp
Correct Answer:- Option-C
Question76:-The contract ratio for the LED TV is defined as
A:-The difference b/w bright and dark portions
B:-The difference b/w most bright and most dark portions
C:-The most bright portion divided by most dark portions
D:-The most bright portion into most dark portion
Correct Answer:- Option-B
Question77:-LCD/LED display panel are usually made in
A:-1 cm to 100 cm
B:-2.5 cm to 125 cm
C:-3 cm to 300 cm
D:-6 cm to 160 cm
Correct Answer:- Option-D
Question78:-semi automatic washing machine consist of 2 tubs one is wash tub and the other is
A:-Spin tub
B:-Agitator tub
C:-Pulsator tub
D:-Cleaning tub
Correct Answer:- Option-A
Question79:-Generally the HP of motor used in a washing machine is
A:-0.1 to 0.15 HP
B:-0.3 to 0.5 HP
C:-1.0 to 3.0 HP
D:-1.5 to 3.5 HP
Correct Answer:- Option-B
Question80:-A microwave oven works on _____ frequency
A:-1.45GHz
B:-2.45GHz
C:-3.45GHz
D:-1.5 – 3.5GHz
Correct Answer:- Option-B
Question81:-A vacuum cleaner cleans carpets etc on the principle of
A:-Radiation
B:-Suction
C:-Dispersion
D:-Absorption
Correct Answer:- Option-B
10 of 13
Question82:-A vacuum cleaner does not run but gives buzzing sound when the defect lies in its
A:-Main fuse
B:-Socket
C:-Armature winding
D:-Capacitor
Correct Answer:- Option-C
Question83:-A mixer grinder grinds food grains by employing
A:-2 grinding stones
B:-High speed spinning blade
C:-Low speed spinning blade
D:-Crushing blade
Correct Answer:- Option-B
Question84:-The testing of a mixer grinder is called _____
A:-Inching
B:-Plugging
C:-Loading
D:-Mixing
Correct Answer:- Option-A
Question85:-KU band used for satellite communication is _____
A:-10.0 to 19.0 GHz
B:-10.7 to 19.7 GHz
C:-20.0 to 31.0 GHz
D:-20.7 to 31.7 GHz
Correct Answer:- Option-B
Question86:-Frequency band referred as 6/4 GHz is named as
A:-L band
B:-C band
C:-KU band
D:-KA band
Correct Answer:- Option-B
Question87:-A dish antennae used in DTH service consist of a paraboloid reflector of about ____ diameter
A:-15 cm to 30 cm
B:-25 cm to 50 cm
C:-45 cm to 90 cm
D:-115 cm to 150 cm
Correct Answer:- Option-C
Question88:-LNB stands for
A:-Less noisy block
B:-Low noise block
C:-Left norm balloon
D:-Linear norm block
Correct Answer:- Option-B
Question89:-The set top receivers output lies in the frequency band of
A:-30 to 300 MHz
B:-300 to 3000 MHz
C:-600 to 900 MHz
D:-900 to 1400 MHz
Correct Answer:- Option-D
Question90:-A transponder is a _____
A:-Sort of transmitter
11 of 13
B:-Sort of relay station
C:-Frequency channel used by a satellite station
D:-None of the above
Correct Answer:- Option-C
Question91:-A CCTV security system installed in border areas for day and night watch contains a _____ CCTV camera
A:-Infrared
B:-Day and night
C:-Dome
D:-PTZ
Correct Answer:- Option-A
Question92:-The output of a CCTV camera should be
A:-0.1 V P-P
B:-1.0 V P-P
C:-10 V P-P
D:-5 V P-P
Correct Answer:- Option-B
Question93:-The smallest size CCTV camera is
A:-Dome type
B:-Bullet type
C:-PTZ type
D:-Outdoor type
Correct Answer:- Option-B
Question94:-In DTH system a _____ is necessary in addition to dish antennae and cable etc
A:-LNA
B:-LNB
C:-Set top receiver
D:-Transponder
Correct Answer:- Option-C
Question95:-For watching intruders during totally dark time a CCTV camera is associated with
A:-Search light
B:-Halogen lamp
C:-CCFL
D:-IR LED
Correct Answer:- Option-D
Question96:-Magnetron is an / a _____
A:-Amplifier
B:-Oscillator
C:-Multivibrator
D:-Chopper
Correct Answer:- Option-B
Question97:-Induction heating is a type of _____ heating
A:-A zero frequency
B:-High frequency
C:-Power frequency
D:-None of the above
Correct Answer:- Option-B
Question98:-Forced commutations requires
A:-A pre charged inductor
B:-A pre charged capacitor
C:-An over damped RLC load
12 of 13
D:-A very high frequency AC source
Correct Answer:- Option-B
Question99:-Which part of microwave oven generates micro waves
A:-A generator
B:-Magnetron
C:-Metal mesh
D:-Booster
Correct Answer:- Option-B
Question100:-Application of cycloconverters include
A:-Speed control of AC drive
B:-Induction heating
C:-Static VAr compensation
D:-All of the mentioned
Correct Answer:- Option-D
13 of 13